Download Manual for Model 0 KENMORE ELITE GAS DRYER.Sears PartsDirect has parts, manuals & part diagrams for all types of repair projects Click to Call Click to Chat Chat. Download Manual for Model 0 KENMORE ELITE GAS DRYER.Sears PartsDirect has parts, manuals & part diagrams for all types of repair projects. Download Manual for Model 0 KENMORE ELITE GAS DRYER.Sears PartsDirect has parts, manuals & part diagrams for all types of repair projects. Click to Call Click to Chat. KENMORE ELITE Residential Dryer Manual KENMORE ELITE Residential Dryer Owner's Manual, KENMORE ELITE Residential Dryer installation guides Download the manual. Share; Related manuals Upright Freezer KENMORE ELITE (L0602272) Counter Unit, Gas KENMORE ELITE (L0607154) Counter Unit. The height from the bottom of the Kenmore Elite HE3 dryer to the top of the control panels measures 38 inches. The width of the Elite HE3 dryer comes in at 27 inches with a depth of 31.5 inches. The washer model weighs in at 245 pounds, with the dryer unit coming in at 142 pounds for electrical and 147 pounds for gas.
- Kenmore Elite He3 Gas Dryer Manual
- Kenmore Elite He3 Gas Dryer Manual Parts
- Kenmore He3 Dryer Troubleshooting Guide
Kenmore Elite 91582 7.4 cu. Gas Dryer with Steam - White Kenmore 78132 8.8 cu. Gas Dryer w/ SmartDry Ultra Technology - White Kenmore 79133 8.8 cu. Gas Dryer w/ Steam Refresh - Metallic. Feb 25, 2013 Kenmore He3 dryer - fuse replacement. How to replace a dryer heating element on a Kenmore Elite HE3 - Duration. Kenmore Gas Dryer - No Heat - Fix it Yourself! Kenmore Elite HE3 Parts. Some parts shown may not be for your model. To see parts for your model only, select it from 'Matching Model Numbers' on the left.
- 2Table of Contents
- 2Protection Agreements
- 3Warranty
- 4Important Safety Instructions
- 5Installation Requirements
- 5Tools and Parts
- 5Options
- 6Location Requirements
- 6Washer Dimensions
- 6Recommended Installation Spacing for Custom Undercounter Installation
- 6Recommended Installation Spacing for Recessed or Closet Installation, With or Without a Pedestal
- 7Recommended Installation Spacing for Recessed or Closet Installation, With Stacked Washer and Dryer
- 7Recommended Installation Spacing for Cabinet Installation
- 7Drain System
- 8Electrical Requirements
- 9Connect the Inlet Hoses
- 9Installation Instructions
- 9Remove Transport System
- 10Route the Drain Hose
- 10Secure the Drain Hose
- 10Complete Installation
- 10Lever the Washer
- 11Features and Benefits
- 12First Wash Cycle Without Laundry
- 12Regular Wash Cycles
- 12Washer Use
- 12Starting Your Waster
- 12For All Wash Cycles
- 13Using the Dispenser
- 13Choosing the Right Detergent
- 13To Fill Dispenser Compartments
- 13Main Wash Detergent Compartment
- 14Pausing or Restarting
- 14Changing Cycles, Options and Modifiers
- 14Chlorine Bleach Compartment
- 14Fabric Softener Compartment
- 15Status Lights
- 15Wash Cycles
- 15Adding Clothes
- 15Locking Controls
- 16Preset Cycle Settings
- 16Clean Washer
- 16Rinse/Drain & Spin
- 16Handwash/Delicate
- 17Normal Washer Sounds
- 17Soak
- 17Delay Start
- 18Modifiers
- 18Wash Temp
- 18Auto Temp Control
- 18Laundry Guide
- 19Laundry Tips
- 19Preparing Clothes for Washing
- 19Sorting
- 19Loading
- 20Cleaning Your Washer
- 20Cleaning the Door Seal
- 20Washer Maintenance Procedure
- 20Cleaning the Dispenser Drawer
- 21Water Inlet Hoses
- 21Vacation, Storage, and Moving Care
- 22Troubleshooting
12
Install Vent System
1. Install exhaust hood. Use caulking compound to seal exterior
wall opening around exhaust hood.
2. Connect vent to exhaust hood. Vent must fit inside exhaust
hood. Secure vent to exhaust hood with 4' (10.2 cm) clamp.
3. Run vent to dryer location. Use the straightest path possible.
See “Determine vent path” in “Plan Vent System.” Avoid 90º
turns. Use clamps to seal all joints. Do not use duct tape,
screws or other fastening devices that extend into the interior
of the vent to secure vent.
Install Leveling Legs
1. To protect the floor, use a large flat piece of cardboard from
the dryer carton. Place cardboard under the entire back edge
of the dryer.
2. Firmly grasp the body of the dryer (not the console panel).
Gently lay the dryer on the cardboard. See illustration.
3. Examine the leveling legs. Find the diamond marking.
4. Screw the legs into the leg holes by hand. Use a wrench to
finish turning the legs until the diamond marking is no longer
visible.
5. Place a carton corner post from dryer packaging under each
of the 2 dryer back corners. Stand the dryer up. Slide the
dryer on the corner posts until it is close to its final location.
Leave enough room to connect the exhaust vent or gas line.
For mobile home use
Gas dryers must be securely fastened to the floor at the time of
installation.
Mobile home installations require a Mobile Home Installation Kit.
For more information, please call 1-800-4-MY-HOME
®
(1-800-469-4663).
Level Dryer
Check the levelness of the dryer. Check levelness first
side to side, then front to back.
If the dryer is not level, prop up the dryer using a wood block.
Use a wrench to adjust the legs up or down and check again for
levelness.
Make Gas Connection
1. Remove the red cap from the gas pipe.
Kenmore Elite He3 Gas Dryer Manual
2. Using a wrench to tighten, connect the gas supply to the
dryer. Use pipe-joint compound on the threads of all non-
flared male fittings. If flexible metal tubing is used, be sure
there are no kinks.
NOTE: For LP gas connections, you must use pipe-joint
compound resistant to the action of LP gas. Do not use
TEFLON
®†
tape.
WARNING
Excessive Weight Hazard
Use two or more people to move and install dryer.
Kenmore Elite He3 Gas Dryer Manual Parts
Failure to do so can result in back or other injury.
A. Flared male fitting
B. Non-flared male fitting
A
B
†
®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
